Latest Articles

OUTPUT SHAFT INSTALLATION Tools Required

{ No Comment }

J 29837-A Output Shaft Support Fixture. See Special Tools. Installation Procedure Fig. 299: View Of Output Shaft Courtesy of GENERAL MOTORS CORP. IMPORTANT: It is important to note that the input shaft may need a light tap to fully seat into position. If the input shaft is not completely engaged, the output shaft to input […]

INTERNAL TRANSMISSION SPEED SENSOR ROTOR REPLACEMENT Tools Required

{ No Comment }

• J 8433 Two Jaw Puller • J 21427-A Speedometer Gear Puller Adapter. See Special Tools. • J 36352 Speed Sensor Rotor Installer Kit. See Special Tools. Removal Procedure Fig. 296: Identifying Output Shaft Seal & Output Shaft Sleeve Courtesy of GENERAL MOTORS CORP. 1. Inspect the internal transmission speed sensor rotor (699) for cracks […]

INPUT INTERNAL GEAR, REACTION SHAFT AND SHELL INSTALLATION

{ No Comment }

Tools Required J 36850 Transjel Lubricant Installation Procedure Fig. 295: View Of Input Internal Gear, Reaction Shaft & Sun Shell Courtesy of GENERAL MOTORS CORP. 1. Install the reaction sun shell (670) into the reaction sun gear. 2. Install the thrust bearing (669) using J 36850 onto the reaction carrier shaft, tangs up, toward the […]

REACTION CARRIER SHAFT REPLACEMENT Tools Required

{ No Comment }

• J 8092 Universal Driver Handle – 3/4 in – 10 • J 7004-A Universal Remover. See Special Tools. • J 23907 Slide Hammer with Bearing Adapter • J 25019-14 Stator Pump Bushing Remover • J 29369-2 Bushing and Bearing Remover 2-3 in • J 34196-B Transmission Bushing Service Set. See Special Tools. Removal Procedure […]

REACTION SUN GEAR INSTALLATION

{ No Comment }

Tools Required • J 34196-B Transmission Bushing Service Set. See Special Tools. • J 8092 Driver Handle Installation Procedure IMPORTANT: Do not remove the retaining ring (671), except to replace it. Fig. 285: Inspection Areas On Reaction Sun Gear Courtesy of GENERAL MOTORS CORP. 1. Inspect the reaction sun gear (673) for the following defects: […]

LOW AND REVERSE CLUTCH SUPPORT DISASSEMBLE

{ No Comment }

Courtesy of GENERAL MOTORS CORP. 1. Remove the low and reverse roller clutch race (675) from the low and reverse clutch support (679). Inspect the race for damage and surface finish. 2. Remove the two low and reverse roller retainer rings (677) and the low and reverse roller clutch assembly (678). Inspect the roller clutch […]

REACTION GEAR AND CARRIER INSTALLATION

{ No Comment }

Tools Required J 36850 Transjel Lubricant Installation Procedure Fig. 272: View Of Reaction Carrier/Support Thrust Bearing Assembly Courtesy of GENERAL MOTORS CORP. 1. Install the reaction gear support to case bearing (692) onto the internal reaction gear support (685). Retain the bearing using J 36850 or equivalent. 2. Install the internal reaction gear (684) and […]

INNER MANUAL LINKAGE INSTALLATION

{ No Comment }

Fig. 266: Locating Parking Brake Pawl & Return Spring Courtesy of GENERAL MOTORS CORP. 1. Install the parking lock bracket (86). NOTE: Refer to Fastener Notice. 2. Install the parking lock bracket bolt (87). Tighten: Tighten the bolt to 31 N. m (23 lb ft). 3. Inspect the following items: • The parking brake pawl […]

LOW AND REVERSE CLUTCH PISTON INSTALLATION

{ No Comment }

Tools Required • J 23327-1 Forward Clutch Spring Compressor (Bridge). See Special Tools. • J 34627 Snap Ring Remover and Installer. See Special Tools. • J 36850 Transjel Lubricant Installation Procedure Fig. 263: Installing Transmission Seals Onto Low And Reverse Clutch Piston Courtesy of GENERAL MOTORS CORP. 1. Install the transmission (low and reverse clutch […]

MANUAL SHIFT SHAFT SEAL INSTALLATION

{ No Comment }

Fig. 262: Installing Manual Shaft Seal Courtesy of GENERAL MOTORS CORP. Install a new manual shaft seal (82).