Latest Articles

3-4 ACCUMULATOR INSTALLATION

{ No Comment }

1. Inspect the 3-4 accumulator piston (44) for the following conditions: 45 Fig. 436: Identifying 3-4 Accumulator Piston & Piston Oil Seal Ring Courtesy of GENERAL MOTORS CORP. • Porosity • Cracks • Scoring • Nicks and scratches 2. Install the 3-4 accumulator piston oil seal ring (45) on the 3-4 accumulator piston (44). Fig. […]

TURBINE SHAFT O-RING INSTALLATION

{ No Comment }

Fig. 412: Identifying Turbine Shaft O-Ring Courtesy of GENERAL MOTORS CORP. Install the O-ring (618) on the turbine shaft. O-Ring location is location dependent. CONTROL VALVE BODY DISASSEMBLE Fig. 413: View Of Manual Valve Courtesy of GENERAL MOTORS CORP. CAUTION: Refer to Valve Springs Can Be Tightly Compressed И J 1 Caution. Fig. 414: Exploded […]

CONVERTER HOUSING INSTALLATION Tools Required

{ No Comment }

J 41510 T-50 Plus Bit. See Special Tools. Installation Procedure Fig. 411: View Of Oil Pump Seal, Converter Housing & Bolts Courtesy of GENERAL MOTORS CORP. • Ensure the converter housing and case face are clean before installing a new pump seal. • When installing a new oil pump seal (5), the seal will protrude […]

OIL PUMP COVER AND BODY ASSEMBLE Tools Required

{ No Comment }

J 21368 Pump Body and Cover Alignment Band. See Special Tools. Assembly Procedure О Fig. 399: View Of Oil Pump Cover & Oil Pump Body Courtesy of GENERAL MOTORS CORP. 1. Place the oil pump cover onto the oil pump body and put stator shaft through a hole in the bench. 2. Install the pump […]

OIL PUMP STATOR SHAFT BUSHING REPLACEMENT

{ No Comment }

Tools Required • J 7004-A Universal Remover. See Special Tools. • J 8092 Universal Driver Handle – 3/4 in – 10 • J 21465-01 Bushing Service Set. See Special Tools. • J 25019-14 Bushing Installer • J 34196-B Transmission Bushing Service Set. See Special Tools. Removal Procedure Fig. 389: Locating Pump Cover, Check Valve Retainer, […]

OIL PUMP BODY ASSEMBLE Assembly Procedure

{ No Comment }

• J 25016 Pump Seal and Speedometer Gear Installer. See Special Tools. • J 36850 Transjel Lubricant Fig. 380: Installing Oil Seal Assembly Courtesy of GENERAL MOTORS CORP. Fig. 381: View Of Fluid Seal Retainer Courtesy of GENERAL MOTORS CORP. Fig. 382: Installing O-Ring Seal & Oil Seal Ring Courtesy of GENERAL MOTORS CORP. 3. […]

OIL PUMP BODY BUSHING REPLACEMENT Tools Required

{ No Comment }

• J 41778-1 Pump Body Bushing Installer/Remover. See Special Tools. • J 41778-2 Pump Body Bushing Position Stop. See Special Tools. Procedure Fig. 375: Inspecting Oil Pump Body Courtesy of GENERAL MOTORS CORP. 1. Inspect the oil pump body for the following: • Worn or damaged bushings • Foreign material or debris • Porosity • […]

OIL PUMP DISASSEMBLE

{ No Comment }

Fig. 369: Identifying Oil Pump Thrust Washer Courtesy of GENERAL MOTORS CORP. 1. Remove the thrust (pump to drum) washer (601). 2. For pump assemblies with an ISS hole plug (248), remove plug bolt (247) and ISS hole plug (248). 3. Remove the O-ring (249) and discard. Fig. 370: View Of Oil Pump Cover & […]

2-4 BAND ASSEMBLY INSTALLATION

{ No Comment }

Fig. 367: View Of 2-4 Band Assembly Courtesy of GENERAL MOTORS CORP. 1. Inspect the 2-4 band assembly (602) for damage or wear. 2. Install the 2-4 band (602) into the case. Fig. 368: Identifying Band Anchor Pin Courtesy of GENERAL MOTORS CORP. 3. Install the band anchor pin (41) into the case. 4. Index […]

REVERSE INPUT CLUTCH ASSEMBLE Tools Required

{ No Comment }

• J 23327-1 Forward Clutch Spring Compressor (Bridge). See Special Tools. • J 25018-A Clutch Spring Compressor Adapter. See Special Tools. • J 44571-1 Reverse Input Clutch Piston Installer. See Special Tools. Assembly Procedure 607 Fig. 358: Locating Inspection Areas On Reverse Input Clutch Piston Courtesy of GENERAL MOTORS CORP. 1. Inspect the reverse input […]